Skip to main content

Manual & Safety

200W GigE PoE Injector

Model LG-YSNEPPU20010A


Thank you for choosing our 200W Gigabit-Ethernet PoE Injector.

Package Contents

1 x PoE Injector

⚠ WARNINGS & Safety Information

  • Before using the device, carefully read this manual.
  • Keep this manual either downloaded or printed in a safe place for later use. It contains important information.
  • Never connect the device to 230/110/mains voltage! This is extremely dangerous.
  • Avoid placing any objects that could short-circuit the input power cables.
  • Securely connect the cables to the device by firmly inserting them into the cable connectors.
  • Securely mount the device on a stable, level surface to prevent it from falling.
  • Do not cover or obstruct the device to allow for proper heat dissipation.
  • The device should not be opened or repaired by unauthorized personnel.
  • To prevent damage from water or moisture, the device must not be used in wet or humid environments.
  • Only use the device within the specified limits. Do not overload the device.

  • Verify that the PoE adapter provides the correct power voltage for the device and that the power pins are compatible. For this model it will be +V: 1,2,3,6 -V: 4,5,7,8 - always verify on the device label!
  • Ensure proper grounding by connecting the provided ground screw to a grounding point.
  • Ensure you are using an appropriate wire diameter. Choosing the wrong wire diameter is a fire hazard!

rohs_compliance.png ce-mark-c50.png

Additional (compliance) labels for your region may be found on the packaging or the device itself.


This appliance follows the European Union's WEEE directive (2012/19/EU) for responsible end-of-life handling.

  • Packaging: Eco-friendly materials make it easy to recycle. Send that cardboard on its next adventure or recycle it accordingly.
  • Waste equipment: Don't let it gather dust! Your local retailer or recycling center gladly welcomes it back for reuse or responsible recycling. Ask them for the latest disposal routes, and watch your old appliance become something new!


Attach cable connectors to the power cable. Connect the power cable to the positive and negative poles on the device. Make sure that your power supply is in the voltage range stated on the device and is outputting the correct voltage level for your PoE device. Ensure the device is grounded properly.

Wiring Diagram

Please see the following wiring diagram for installation. Please note that using the Starlink Dishy Cable to Ethernet Adapter is also possible instead of using a modified Starlink cable.

Using a modified (re-crimped) RJ45 plug


Using the Dishy Cable to Ethernet Adapter



Please only turn the device on or power it up after the PoE load is connected. The LED on the device will turn solid green, to indicate that the power output is on.


Maintain the device's cleanliness by regularly wiping it with a dry, lint-free cloth. Do not use harsh chemicals or abrasive materials to clean the device, as these may scratch or damage its surface.

LED Status & Fault Codes




⦿ Green LED

Normal Operation

The PoE injector is powering the connected device normally.

White LED


The PoE injector is starting up. (~3s)

 Blinking yellow LED


Voltage on the input is below 40V.

⦿ Red LED

Short Circuit/Overcurrent Protection 

There is a short circuit on the output side of the PoE injector or the PoE-powered device is trying to use too much power.

 Blinking red LED


There is an overvoltage condition on the voltage input side of the PoE injector.

⦿  Red LED with a short blue flash

Device Locked (Short Circuit Recovery Attempts Exceeded)

The PoE injector has detected a short circuit and has exceeded its recovery attempts. The device must be power cycled to clear the code.

We are not affiliated, associated, authorized, endorsed by, or in any way officially connected with Starlink, SpaceX, or any of its subsidiaries or affiliates.

Imported by performeon UG (haftungsbeschränkt), Dachauer Str. 112, 80636 Munich, Germany ● +49 (0) 89 2000 85 320

Manufactured by YiMotion Industries Co. Ltd, 8 floor, C building, KaiWo, KengZi, Pingshan District, Shenzhen City, Guangdong Province, China.